Clopyralid 3 Herbicide is used for the control of broadleaf weeds such as acacias artichoke, buckwheat, buffalobur, chamomile, clover, cocklebur, coffeeweed, dandelion, dock, groundsel, hawkweed, horseweed, knapweed, locoweed, mesquite, nightshade, pineappleweed, ragweed, smartweed, sorrel, sowthistle, sunflower, thistle, and many other listed weeds.
For Use In
Clopyralid 3 Herbicide is for use in non-crop areas, forestry sites, industrial manufacturing sites, storage sites, rights-of-way, wildlife openings, grazed areas on listed sites, tree plantations, range lands, and grass pastures.,
Application Timing: Apply to actively growing weeds. Extreme growing conditions such as drought or near freezing temperatures prior to, at, and following time of application may reduce weed control. Only weeds that have emerged at the time of application will be affected. Wet foliage at the time of application may decrease control. The treatment with ALLIGARE CLOPYRALID 3 will be rainfast within 2 hours after application.
Application Rates: Generally, application rates at the lower end of the recommended rate range will be satisfactory for young, succulent growth of susceptible weed species. For less sensitive species, perennials, and under conditions where control is more difficult (plant stress conditions such as drought or extreme temperatures, dense weed stands and/or large weeds), the higher rates within the rate range will be needed.
Use of Adjuvants: Addition of surfactants, crop oils, or other adjuvants may increase effectiveness of ALLIGARE CLOPYRALID 3 herbicide. If an adjuvant is added to the spray solution, follow all manufacturer use guidelines.
Spray Coverage: Use sufficient spray volume to provide thorough coverage and a uniform spray pattern. Do not broadcast apply in less than 2 gallons of total spray volume per acre. For best resultsand to minimize spray drift, apply in a spray volume of 10 or more gallons per acre. As vegetative canopy and weed density increase, spray volume should be increased to obtain equivalent weed control. Use only nozzle types and spray equipment designed for herbicide application. To reduce spray drift, follow precautions under Avoiding Injury to Non-Target Plants.
Cut Surface Treatments: Apply ALLIGARE CLOPYRALID 3 in rights-of-way and other noncrop areas to control unwanted trees and vines in the legume family such as mimosa, locust, redbud and wisteria.
Stump Treatment: Spray or paint the cut surfaces of freshly cut stumps and stubs with a 50/50 mix of ALLIGARE CLOPYRALID 3 and water. The cambium area next to the bark is the most vital area to wet. This should be done as soon as the tree or vine has been cut.
Each 2.5 gallon container of Clopyralid 3 Herbicide will cover approximately 16.36 acres if used at the higher mix rates per acre.
Time to Kill
GENERAL INFORMATION ALLIGARE CLOPYRALID 3 herbicide is recommended for postemergence control of broadleaf weeds and select woody brush species in non-cropland areas including equipment pathways, industrial manufacturing and storage sites, forest sites, and rights-of-way (such as along roadsides, electrical lines and railroads). Use on these sites may include application to grazed areas as well as establishment and maintenance of wildlife openings, wild parkland and wildlife management areas, and forest spot application adjacent to these sites. ALLIGARE CLOPYRALID 3 is labeled for control of broadleaf weeds in cottonwood/poplar and eucalyptus tree plantations; and in rangeland and permanent grass pastures in certain western states.
Country of Manufacture
For control of broadleaf weeds, apply 1 /4 to 1 1/3 pints per acre of ALLIGARE CLOPYRALID
3 (equivalent to 0.09 to 0.5 lb acid equivalent per acre)
For control of broadleaf weeds and woody brush in non-cropland areas, forest sites, industrial manufacturing and storage sites, rights-of-way, and wildlife openings including grazed areas on these sites, tree plantations, and rangeland and permanent grass pastures.