Finale Herbicide 2.5 gallon 11.33% glufosinate-ammonium

Pests controlled

Broadleaf weeds:

Burdock, chickweed, clover, common cocklebur, dandelion, dogbane, filaree, jimsonweed, Kochia, London rocket, Malva, marestail, purslane, shepherd’s purse, smartweed

Grasses and sedges:

Annual bluegrass, barnyard grass, crabgrass, cupgrass, fall panicum, fescue, giant foxtail, goose grass, Kentucky bluegrass, lovegrass, shattercane, smallflower Alexander, stinkgrass, windgrass, yellow foxtail

Woody species:

Blackberry, conifers, greenbriar

FINALE® Herbicide is a nonselective water-soluble herbicide for application as a foliar spray for the control of a broad spectrum of emerged annual and perennial grass and broadleaf weeds.

FINALE® Herbicide will also control certain woody species. Plants that have not yet emerged at the time of application will not be controlled.

THOROUGH SPRAY COVERAGE IS IMPORTANT. Visual effects and control from application of FINALE® Herbicide occur within 2 to 4 days after application under good growing conditions.

This product is nonselective and will injure or kill all green vegetation contacted by the spray. Avoid all contact with foliage or green tissue of desirable vegetation.

Avoid direct spray contact with green, thin, or uncalloused bark of desirable vegetation or plant injury may result. If desirable vegetation is contacted, rinse the sprayed portion with water immediately.

FINALE® Herbicide works best when weeds are actively growing. Weed control may be reduced when applications are made to weeds under stress due to drought or cool temperatures. Weeds under stress or in dense populations will require application at the highest rate recommended.

Refer to the How to Apply section of this label.

When applied as recommended in this label, FINALE® Herbicide controls annual and perennial weeds. Refer to the How to Apply section of this labeling for recommended rates and a list of weeds controlled. Applications may be made on a broadcast, banded or spot treatment basis depending on the situation. Avoid direct spray or drift to desirable vegetation. Regrowth may occur due to the weed stage of growth at application, low use rate, or environmental conditions. Repeat treatments may be necessary to control plants generating from underground parts or seed.

WHEN TO APPLY

FINALE® Herbicide is a foliar-active material. Best results are obtained when weeds are actively growing. Weed control may be reduced when applications are made to weeds under stress due to drought or cool temperatures. Weeds under stress or in dense populations will require application of the highest rate recommended. Refer to the How to Apply section of this label.

FINALE® Herbicide should be applied at the rate recommended in the How to Apply section of this label. Repeat applications of

FINALE® Herbicide or tank mixes of FINALE® Herbicide plus one or more appropriate residual herbicide(s) listed on this label will be needed to control weeds emerging from underground parts or seeds.

HOW TO MIX

FINALE® Herbicide must be mixed with water to make a finished spray solution as follows:

1. Fill the spray tank with the required amount of water.

2. Add the proper amount of this product, then mix thoroughly.

USE PRECAUTIONS

1. DO NOT apply this product through any type of irrigation system.

2. DO NOT apply directly to or allow drift to contact desirable green tissue or green, thin, or uncalloused bark of desirable vegetation.

3. FINALE® Herbicide is rainfast in a minimum of one-half hour and an average of 4 hours after application depending upon weed species, environmental conditions, and herbicide application rate.

4. DO NOT allow grazing of vegetation treated with this product.

5. Plants may be safely planted into Finale treated areas after spray has dried.

How To Apply

Spot or Directed Applications

This product may be used as a spot- or directed spray-application using 2 to 4 fluid ounces per gallon of water. Mix 2 to 4 fluid ounces per gallon of water depending upon the weed and stage of growth as shown in the following sections. Spray undesirable vegetation foliage on a spray-to-wet basis. Do not apply beyond runoff. Ensure uniform and complete coverage. Use a coarse spray. Do not spray during windy conditions. Backpack, pump-up, and hydraulic sprayers may be used. Thoroughly clean the sprayer following use.

Broadcast or Boom Applications

Apply 2 to 6 quarts per acre depending upon the weed and stage of growth as shown in the following sections. Use a minimum of 40 gallons of water per acre with a minimum of 30-psi spray pressure.

Aerial Applications

Apply as a foliar treatment using a minimum of 5 gallons of water per acre to ensure thorough coverage. Do not apply when winds are gusty or under condition which favors drift on to desirable vegetation. Applications under conditions, which cause drift of this product, will result in damage to any vegetation contacted. Drift control additives may be used. If a drift control additive is used, observe and follow all directions and precautions as specified on the additive label.

Tank Mix Recommendations for Noncrop Uses

FINALE® Herbicide is compatible in tank mixes with many other herbicides including non-selective herbicides such as Roundup®. Follow the more restrictive label limitations and use precautions for each product. No label dosage rates should be exceeded. Tank mix applications of FINALE® Herbicide plus the following herbicides are recommended for broad-spectrum postemergence and preemergence weed control.

Along with non-selective herbicides, ePestSolutions also offers a wide variety of selective herbicides and both post and pre-emergent weed control products with free shipping!